AEG Washing Machine displays an error code - causes and solutions

Issue

If your AEG washing machine displays an error code, if your washing machine is beeping and flashing lights, or if the wash cycle stops unexpectedly and a fault code appears on the display, the electronic control system has detected a condition that requires attention. Error codes help identify the affected system, allowing you to diagnose the issue more quickly and often resolve it without requiring a repair visit.

Typical signs include:

• Error code beginning with "E" followed by numbers appears on the display
• Washing machine stops during a wash cycle
• Washer dryer emits beeps or flashing LEDs
• The drum stops rotating during the programme
• Water remains in the drum after the cycle
• The door remains locked after the programme ends

Applies to

• AEG Washing Machines
• AEG Washer Dryers

Resolution

Start by checking the most common causes of the problem. In many cases, the issue can be resolved without service.

AEG washing machines continuously monitor key functions such as water intake, drainage, heating, motor operation, door locking, and electronic communication. When the system detects abnormal operating conditions, it displays an error code to help identify the affected component or function.

Use the guides below to find the meaning of your error code and the recommended troubleshooting steps:

• Error code E10 or similar (water supply problem)
• Error code E20 or similar (draining problem)
• Error code E30 or similar (water pressure sensor problem)
• Error code E40 or similar (door lock problem)
• Error code E50 or similar (motor problem)
• Error code E60 or similar (heating problem)
• Error code EF0 or similar (water leakage, over-foaming, imbalanced load)
• Error code EH0 or similar (power supply problem)

If your error code is not listed:

1. Note the complete error code displayed on the washing machine.
2. Visit the AEG Support website.
3. Enter the error code in the support page search field.
4. Open the article matching the displayed code.
5. Follow the troubleshooting steps provided for your model.

If the troubleshooting article recommends a reset, reset the washing machine by:

1. Disconnecting power at the wall socket or circuit breaker.
2. Waiting around 1 minute.
3. Reconnecting power.
4. Checking whether the issue has been resolved.

For model-specific information, operating instructions, and additional fault code guidance, refer to your user manual.

Important

• Different AEG washing machines may use different fault code variants.
• Always record the complete error code before disconnecting power.
• Some error codes indicate a temporary operating condition, while others may indicate a component fault.
• Repeated fault codes generally indicate that the underlying issue remains present.

When Is It A Genuine Fault?

In these situations, there may be a fault with the electronic control system, motor, heating circuit, sensors, or another component:

• The same error code returns immediately after troubleshooting.
• The washing machine will not start any programme.
• The drum does not rotate.
• Water will not enter or drain from the washing machine despite completing the recommended checks.
• Multiple error codes appear repeatedly.
• There is evidence of water leakage, burning smells, or visible damage.

Looking for more washing machine maintenance and repair advice?

Visit our Washing Machine Expert Q&A for answers to commonly asked questions from our repair specialist.

Still need help? Get expert support

If the issue continues, a professional technician can help diagnose and fix the problem.

No matter if your appliance is in warranty, out of warranty, or covered by an appliance protection plan - we’ll guide you to the right service.

Book a repair online

Cause

AEG washing machines use multiple sensors, control circuits, and safety monitoring systems to ensure correct operation throughout the wash cycle. When a parameter moves outside its expected range, the electronic controller records the condition and displays a fault code.

The most common causes are:

• Restricted or interrupted water supply
• Drain pump or drainage system blockages
• Door lock mechanism faults
• Motor or drive system faults
• Heating element or temperature sensor issues
• Excessive detergent foam affecting water level detection
• Water leakage detected within the washing machine
• Electrical supply irregularities
• Communication faults between electronic components

Displaying an error code helps protect the washing machine from further damage while directing troubleshooting towards the affected system. Understanding the code allows a more accurate diagnosis and helps determine whether the issue can be resolved at home or requires professional repair.

FAQ – AEG Washing Machine Error Codes

Why is my AEG washing machine showing an error code?

The electronic control system has detected an abnormal operating condition and is providing diagnostic information.

What does an error code tell me?

The code identifies the system or function where the fault was detected, such as water intake, drainage, heating, or motor operation.

Can I continue using the washing machine when an error code is displayed?

This depends on the fault. Many error codes stop the programme to prevent damage or poor washing performance.

Where can I find information about my specific error code?

Search for the code on the AEG Support website or consult your user manual.

Is it normal for the washing machine to beep when showing an error code?

Yes. Beeps and flashing indicators are normal warning methods used to draw attention to a detected issue.

When should I book a repair?

If the same error code returns after troubleshooting, or if the washing machine cannot complete a wash cycle, professional diagnosis may be required.